ABSOLUTE Digimatic Indicators Signal ID-C Series 543 This is an externally-powered Digimatic Indicator with a N-ch open drain –NG, OK, +NG output. • Dust-protected and protected against splashing water, complying with IEC 60529 (equivalent to IP54) • Measures MAX/MIN/RANGE (run-out value). • Saves three different Preset and Tolerance settings. • Fast measurement frequency mode (detection cycle 50 times/s) for reliable measurement in the peak detection mode (MAX/MIN/RANGE) • Calculation function Ax. Coefficient A freely definable, x = displacement of the plunger • Analogue bar graph in the display (12 different scales switchable) • GO/±NG tolerance judgment function 543-350B-10 28.5 20 ø10.9 7.6 ø54 ø59.4 7.3 37.2 13.8 13.3 67.4 43.5 50.1 5 Cable: 4 m ø8 0 −0.009 20 Ball contact (ø3) 901312 (threaded: M2.5×0.45) ø6.5 Metric No. Range [mm] Digital step Max. Permissible Error E MPE H MPE (Hysteresis) R MPE (Repeatability) Measuring force MPL Protection Mass [g] 543-350B-10 12,7 0,001 mm/ 0,01 mm 0,003 mm 0,002 mm 0,002 mm ≤2,5 N IP54 285 543-350-10 12,7 0,001 mm/ 0,01 mm 0,003 mm 0,002 mm 0,002 mm ≤2,5 N IP54 295 No. with "B": flat back plate Logic of output signal Signal name Tolerance judgment results Sensor signal synthesizing error Overflow error of display value -NG OK +NG Negative logic −NG (Orange) Low High High High OK (Green) High Low High High +NG(Brown) High High Low High Positive logic −NG (Orange) High Low Low Low OK (Green) Low High Low Low +NG (Brown) Low Low High Low Normal mode, Maximum value detection mode, Minimum value detection mode 1.2 kΩ IN GND Switch, etc. DC 5 ~ 24 V Input current: 20 mA or less Circuit input OUT GND Load External power supply Load voltage: 5 ∼ 24 V DC Maximum load current: 100 mA or less Circuit output Functions Series 543 PRESET 3x ON/OFF Analog bar resolution switchable Function lock GO/±NG judgement Signal output: (+NG, OK, -NG) Signal input: No-voltage input, (PRESET_RECALL/ZERO, HOLD_RESET) MAX/MIN/RANGE ABS / INC (INC ZERO) GO/±NG judgement via LED Calculation function (with formula) Counting direction switchable Specifications Display LCD, character height 8 mm Max. response speed Unlimited Measurement frequency (MAX/MIN/RANGE) 100 times/s (if the plunger speed >0,1 mm/s the peak value could not be displayed correctly.) Alarm Counting value composition error, overflow error, tolerance limit setting error Stem ∅ 8 mm Contact point Carbide ball, thread M 2,5 x 0,45 mm Power supply DC 5 - 24 V Optional accessories No. Description 21EZA198 Spindle Lifting Lever, for Digital Indicator, A-Type Dial Indicator Series 2/3/4 21JZA295 Spindle Lifting Cable, for Indicator, L=500 mm 21EZA105 Spindle Lifting Knob, for 12,7mm Range 238774 Silicon rubber boot for ID-C, ID-N, ID-S Consumable spares No. Description 901312 Contact Element Ball Point, M2,5x0,45, 7,3 mm Length, Carbide, Metric 21EAA423 NBR Rubber Boot, Digital Gauge Series 543 GO +NG -NG Application: GO/NG Sorting All products to be sold to commercial customers. Product illustrations are without obligation. Product descriptions, 242 All products to be sold to commercial customers. Product illustrations are without obligation. Product descriptions, in particular any and all technical specifications, are only binding when explicitly agreed upon.
RkJQdWJsaXNoZXIy MTU4ODc4MA==